Home
Plastic And Film Packaging Test Equipment
- Luggage and Suitcase Testing Equipment
- Colorimeter
- Carpet Testing Machine
- Eyeglasses Test Equipment
- Plastic And Film Packaging Test Equipment
- Sample preparation
- Carton Package Testing Equipment
- Toys Testing Instrument
- Environmental Testing Equipment
- Footwear Testing Equipment
-
Textile Testing Equipment
- Zipper & Button & Velcro Tape Tester
- Protective Clothing & Mask Tester
- Gloves & Socks Tester
- Feather & Down Tester
- Nonwoven Textile Tester
- Geotextile Tester
- Flammability Test Equipment
- Yarn and FiberTesting
- Washing & Laundering
- Tensile Burst Tear Strength Tester
- Fabric And Garment Testing
- Dyeing and Finishing Tester
- Color Fastness Testing
- Abrasion and Pilling Tester
0102030405
Plastic Testing Equipment Plastic Film Free-Falling Dart Impact Resistance Tester P003
Overview
The dart impact tester is suitable for measuring the impact mass and energy of plastic film and sheet under free dart impact at a given height. Adopt automatic measurement mode and calculate the impact strength automatically, which is widely used in quality inspection and packaging enterprises.
Test Principle
At the beginning of the falling dart test, the test method was first selected to estimate an initial mass and △ m value.
If the first sample is damaged, apply pressure on the weight △ m to reduce the falling mass.
If the first sample is not broken, it shall be tested successively with a load △ m to increase the falling mass.
In conclusion, using weights to reduce or increase falling mass depends on whether the previous sample is damaged or not.
After the test of 20 samples, the total amount of damage (Marked as N) is calculated.
If N is equal to 10, the test is completed.
If N is less than 10, continue the test until N is equal to 10.
If N is greater than 10, continue the test until the total number of undamaged samples is equal to 10.
Finally, the system will automatically calculate the impact strength of the dart.
Application
Composite films
Plastic Sheet
Standards
GB 9639, ASTM D1709, JIS K7124
Key Parameters
|
Method of measurement |
Method A & B |
|
Impact range |
Method A: 50-2000g Method B: 300-2000g |
|
Accuracy of the test |
0.1g(0.1J) |
|
The sample holder is installed |
Pneumatic |
|
The sample size |
>150*150mm |
|
Air resource |
0.6 Mpa |
|
Working temperature |
15℃-50℃ |
|
Related humidity |
Up to 80%, no condensation |
|
Power supply |
220V, 50HZ |
|
Dimensions |
480mm×470mm×2160mm |
|
Net weight |
70kg |
Product Details
Fixture
Control panel
Production Processes
Process design and design and manufacture of specialized process equipment
Machining of components
Assembly of products
Comprehensive testing of machines
Scenarios of Use
Laboratory
Textile factory
Operation
Connecting the air supply
Connect the air supply to the instrument.
Add distilled water
Connect tube from the freestanding funnel to the water connector located at the back right-hand corner of the SST unit. Add distilled water.
Put in filte
Unscrew the screws and remove the top plate,Take away the reflector.
Put in filter.
Install the xenon lamp
Install the xenon lamp and connect the lamp cabler.Replace the top cover and tighten the set screws.
Mount the sample
Mount the sample on the sample clamp.
BPT Sampling
Place the sample into the test chamber and close the door.Be careful to avoid covering the BPT sensor.
Transportation
Packing System
1. Products are covered with air bubble film before put them into composite board standard export wooden case. To ensure waterproof, moistureproof, corrosion, anti-corrosion and security.
2. Package with shipping mark in line with International and national standards, which is easy for handling, loading and unloading.
3. Packing materials selected accorded with economic and safety requirements
4. Compliance with environmental requirements.
For Metal Box Package
For Carton Package
For Wooden Case
